Measuring for and hanging curtains is simple in lots of conditions and will be accomplished by anybody competent in DIY (do-it-yourself).

Nevertheless, there are some conditions the place it’s advisable to make use of an skilled. These embrace:

• Bay home windows
• Slot home windows; very slender, tall home windows
• Home windows with out adequate wall house above the window for a pole/monitor
• Home windows with out wall house or on both facet
• Non-rectangular home windows (e.g. round, triangular,)

However for many conditions you can be utilizing both a curtain monitor or pole throughout a flat rectangular window. So there are solely two measurements of significance. When measuring use a sturdy metallic tape measure, have a spirit stage useful to examine whether or not poles, batten, flooring and so on are actually stage. Use correct protected steps in case you are working at peak and for giant home windows have an assistant maintain the opposite finish of the tape. The old adage “measure twice and lower as soon as” holds true!

Measuring curtain width

Begin by measuring the width of the window horizontally throughout the recess occupied by the window & its body. [Note the width of a window is not the width of the glazing.] Now add 20-30cm (8-12″), on all sides because the monitor or pole ought to prolong past all sides of the window to allow the curtains to be drawn properly again. A big window has extra material within the curtain and so wants more room both facet to pull again fully. If there’s inadequate house on both facet of the window you might have to regulate your design and it could be higher to get some skilled help.

Chances are you’ll discover a pre-existing picket batten above the window and this could equally prolong past the window aperture. If it doesn’t you might contemplate changing or extending the batten. If you’re becoming a monitor then the batten might be helpful, whereas in case you are becoming a pole the batten will be an obstruction. If you purchase a pole ensure that the pole size (distance between finials) is the same as or larger than the required width and guarantee which you could lower the pole size right down to the specified dimension.

Measuring curtain drop

Curtain drop is the gap between the highest and backside of the material within the completed curtain, and it depends upon the type of curtain heading, positioning of the pole or monitor and the place of the underside of the curtain. When putting in a curtain pole purpose to place it above the window in order that the highest of the curtain material is no less than 10cm / 4inches above the highest of the window recess 용인커튼.

• Curtain Poles with rings: As a rule the highest of the curtain ought to be slightly below the rings so measure the drop from the underside of the ring.
• Curtain pole with eyelet curtains: On this state of affairs there aren’t any curtain rings and the highest of the curtain might be above the pole. Measure the drop from the highest of the pole and add 3.5cm to aloe for the quantity of curtain that might be above the pole.
• Curtain poles with tab high curtains measure drop from the highest of the pole.

For all curtains you want to resolve the place the underside will end:

• Sill size: the curtain ought to end 1cm above the sill (however be aware that this may let extra light into the room).
• Beneath sill size; usually curtains end half method between the sill and a wall mounted radiator. Typically they dangle over the radiator however this channels heat air up backstage and so doesn’t assist maintain the room heat. Resolve the place you need the material to finish.
• Full size; the curtain finishes 1.5cm above the floor. This measurement wants precision as a result of many flooring are usually not completely stage. Measure the drop from an put in pole or monitor in three locations, the centre and to the left & proper. Work with the smallest measurement however double examine that the monitor or pole is stage. If doubtful examine the slope of the floor.
• Pooled; in contrast with full size curtains these normally have an additional 30cm /12 inches of cloth to pool onto the floor

Lastly 

After getting width and drop give these figures to your curtain maker who will have the ability to calculate the amount of cloth you will have and the price of making up the curtains. Additionally, you will must agree on the curtain heading and on the kind of lining in your curtains. All this may occasionally appear onerous work however you’ll find yourself with bespoke made to measure curtains that suit your window completely; one thing that manufacturing facility made curtains not often can obtain.